![]() Opel 603 full R/W Micro, Flash, EEPROM, via k-line & CAN ok ![]() Opel 602/3 full read/write Micro, Flash, EEPROM, via k-line & CAN ok (Be sure to run as administrator using windows 7) Opel – EDC16C9/39, PSG16 via CAN OBD read and write ok Read/write as generic simens SIM4LE boot mode flash 512kB – OK (catalyst off). Kess didn’t want to read this tho ? might of been voltage l read at the guys place(fans on with read and write) and wrote at mine with charger but didn’t try kess again I can’t wait to see if can do edc16c34 5.95 Today I have write another file (good one) with mpps v18 and it was very good. I have write that file with galletto and same problem. ![]() Mpps did not corrupt my eep, file that i was made it was bad, in my happiness and stupidity I put into IQ maps, 65mg fuel without changing IQ limit, 60mg I come back with news about edc16c34 Ford… I would BDM or use any tool other than MPPS whatever version So much so i never ever tried, always same story mpps.Īlways used Fgtech on these, and no issues, MPPS is renown for Issues on the Focus 1.6tdci Edc16 ecu, Yesterday i have tested mpps v18 into my Ford Focus 2 edc16c34.įocus, read 3 sectors about 10 min and write 4,20 min than wait 3 min.Īfter that 3 min I wait another 2 min, like software says. Worked for me.also astra J on 2011 with Denso 1.5mb Linea 2011 Marelli 6F3 read/write OBD Trought K-line, ( FG 54 read only flash trought CAN)įiat Scudo as (Peugeot 3008) 2.0 HDI Delphi DCM 3.5įiat Stilo IAW6JF.P3, through OBD, mpc and eeprom read write for immo-off, all ok.įord Fusion 1.4 TDCi Siemens Sid 804 R/W OBD CAN = OK Peugeot 807 ECU DELPHI DCM 3.5 READ OBD OKĬitroen c5 DCM3.5 read write OBD ok, checksum ok I tried today another edc16u1 and can read and write…Īstra h 1.9 tva off OBD and Zafira B 1.9 EGR off OFF ok, just choose read all( where available) Have done EDC16U1 more than 20 at this moment with no problem! It can even write full flash to EDC1616 Opel So far… MPPS V18 worked on everything l have tested on. * Mpps v18 Windows 7 should be the best solutions of mpps tuning work.įor mpps v18 clone, Windows 7 is 100% OK, WIN XP, WIN 8, WIN 10 needs luck. Tested BMW EDC16C31, read/write OK from windows 8 64bit Windows 10 32 and 64 wish it worked on xp still tho. It works good in win 8 and win 10 both 圆4, software will only start when cable gets power from car. > WIN7: 100% OK, no problem on all cars. The above MPPS hardware is from .uk (Item No. ***Please make sure your MPPS hardware has the same PCB, otherwise you can’t download the above software to work with, I’m afraid the cable will be locked. !9Dpg3JwL!PFVR8bbMhC8HaDhBE075IP8iryOdbHDk3kkBNqmShiw Free Download Nissan Consult 3 Plus V82.Topic: MPPS V18 software download free, tested OS, carlist, reviews (Ford, VAG, Fiat etc).Install Kess v2 5.107 ksuite V2.80 on Win10 64bits Install Mini VCI Techstream Driver on Win10 64bits Repair BMW CAS3+ ISTAP with Autel IM508/IM608Ģ003-2019 BMW Models and CAS/FEM Type Listed Repair Carprog A1 Adapter for CAN BUS cummunicationĬomplete List of Chrysler Group Security Gateway LocationsĪll Benz EIS/EZS Pinouts for Table Connection How to use BMW INPA software and cable K+DCAN How to install TIS2000 for GM Tech 2 scanner Top Tools to Repair Porsche 12V Lithium Battery Install BMW INPA on WinXP Win7 Win8 Win10įree Download BMW E-sys Plus 3.8.1 with Keygenįree ECM Titanium 1.61 with 26000 drivers Maybe i need buy a new one.įree Download TOYOTA Techstream V18.00.008 He says it’s working more stable and fast. It seems much more better in design and quality. Have seen my friend’s mpps v18 ecu flasher pcb. Tested with the car switched on and also off, all good voltage is ok. R7-4.7kohm 5% stock resistor not changed, i’m going to change it but i think there is no difference. Reworked with normal size resistors 1% percent tolerance. Reworked one unit after showing wrong voltage 30 volt. It will pull up lots of the correct surface mount resistors and they will let you order only what you needĪfter that voltage is correct. Just go to any electronics part store such as and type in the 4 digit numbers for search 4702, 4701, 1200. Use 4 digit resistor tolerance 1% or lessįor a farnell codes for R7 ,R8 and R13 Resistors: R13 and R7 and R8 bad because 3digit resistor bigger tolerance 5% ![]() My working clone has the blue board in it. Big thanks to the folk in the MH community. Here are some tips of how to modify and fix it. Maybe there is something wrong with the hardware. It seems to work but shows the wrong voltage. I just picked up a MPPS v16 ecu tuning kit china clone.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |